Home of Genuine Products | Installments available for Govt Employees
Genuine products | Easy installments for Govt Employees

Washing Machine Not Spinning? 8 Causes and Simple Fixes

Washing Machine Not Spinning? 8 Causes and Simple Fixes - SK Electronics buying guide

Quick answer: A washing machine that will not spin is most often reacting to an unbalanced or overloaded load, a lid or door that is not fully closed, or water that cannot drain because of a bent hose or a blocked filter. Spread the clothes evenly, take some out, check the lid, straighten the drain hose and clean the filter, then switch the machine off at the socket for a few minutes and try again. If the motor hums but the drum or spin tub never turns, call a technician.

Why washing machines stop spinning on purpose

Spinning at high speed with a lopsided load shakes the machine hard, so most machines have sensors that slow or stop the spin when they detect a problem. Samsung’s support guide explains that an unbalanced load is a common reason, and that its machines show a code such as “Ub” or “Ur” when it happens. Other brands use their own codes, so check the manual. In many cases the machine is protecting itself, not broken.

8 checks when your washing machine is not spinning

1. Spread the load evenly

Wet clothes bunch on one side, especially a single heavy item such as a blanket or a pair of jeans. Open the lid or door and spread the clothes around the drum. If you are washing one large item, Samsung suggests adding a few more items so the weight does not gather on one side.

2. Do not overload, or underload

Samsung advises leaving about a hand’s width between the top of the laundry and the top of the drum. An overfull drum cannot balance; a drum with one small item can struggle to balance too.

3. On a twin tub, respect the spin tub’s capacity

The spin tub of a twin tub holds less than the wash tub. The Haier 10 kg twin tub lists 10 kg wash and 8 kg spin, the Haier HTW-100-1217W 10 kg wash and 6 kg spin, and the PEL PWM-1050T 10.5 kg wash and 8 kg spin. Spin a full wash in two batches, press the clothes down evenly, and fit the inner spin cover if your model has one.

4. Close the lid or door firmly

Most machines will not spin with the lid or door open. On a twin tub, the spin tub lid must be fully closed; many spin tubs stop when the lid is lifted. On a front load, a door that does not latch stops the cycle.

5. Make sure the machine is level

A machine that rocks on an uneven floor reads as unbalanced. Samsung’s first step is to check that the washer is level and adjust its levelling legs. Do not put it on a loose platform or bricks.

6. Check the drain hose

Most machines will not spin until the water has drained. Straighten any kink or bend in the hose and make sure it is not crushed behind the machine. For automatic machines, Samsung says the hose should go 6 to 8 inches into the drain pipe, sit between 18 and 96 inches high, and not form an airtight seal with the pipe.

7. Clean the drain or lint filter

Coins, hair clips and lint block the drain. Most front load machines have a pump filter behind a small cover at the bottom front; Samsung’s guide is to unplug the machine, drain the water into a container through the emergency tube, unscrew the filter and clean it. Top load and semi-automatic machines often have a lint filter in the tub. Check your manual for where yours is.

8. Restart the machine

Samsung’s tips include switching the washer off and on at the power point and giving it a few minutes before switching it on. Then close the lid or door and start a spin or drain programme.

Haier 10 kg twin tub semi-automatic washing machine with 8 kg spin tub
Haier 10 kg twin tub: 10 kg wash, 8 kg spin, so spin a full wash in two batches.

Not spinning: symptoms and likely causes

What you see Likely cause What to do
Spins a little, stops, tries again Unbalanced or heavy single item Spread the load, add or remove items
Water stays in the drum, no spin Kinked hose, blocked filter or drain Straighten the hose, clean the filter, check the drain pipe
Twin tub spinner will not start Spin lid open, overloaded spin tub, timer not set Close the lid, spin in two batches, turn the spin timer
Spins, but clothes come out very wet Overload, slow spin programme, or a twin tub’s spin cycle cut short Use a higher spin setting, smaller loads, a full spin time
Motor hums, drum does not move Worn belt, clutch or motor fault Call a technician
Loud banging during spin Unbalanced load or machine not level Stop, spread the load, level the machine

When to call a technician

Call for service if the motor runs but the drum or spin tub never turns, if you smell burning, if the machine trips the breaker, or if it still will not spin after all eight checks. Unplug the machine before you open any panel, and do not run a machine that leaks water near its electrical parts. Many of our machines list long warranties, such as 10 years on the Haier twin tubs and 10 years on the motor plus 2 years on parts for the PEL PWMS-1250 T, so keep your warranty card and invoice ready.

How to keep your machine spinning well

  • Load to the capacity on the spec sheet, measured with dry clothes.
  • Wash heavy blankets alone only if your machine is big enough, and add a few towels to balance them.
  • Clean the filter regularly.
  • Keep the machine level and on a firm floor.
  • For faster drying in winter, a high speed spin helps: the Haier HD-6050 spin dryer spins at 1,330 RPM.

Frequently asked questions

Why is my washing machine not spinning?

Usually an unbalanced or overloaded load, a lid or door not fully closed, or water that cannot drain. Spread the clothes, close the lid, straighten the hose and clean the filter, then restart the machine.

Why is my washing machine not spinning but the motor is running?

If you hear the motor but the drum or spin tub does not turn, the belt, clutch or motor drive may be worn or faulty. That needs a technician.

Why does my twin tub spinner not spin?

Check that the spin lid is fully closed, the spin tub is not overloaded and the timer is set. Twin tub spin tubs hold less than the wash tub, so spin a full wash in two batches.

Why are my clothes still wet after the spin?

The load may be too large, the spin speed set low or the spin time too short. A spin dryer or a twin tub’s spinner removes more water than a wash-only machine.

What does an unbalanced load error mean?

The machine has detected that the weight is on one side of the drum and has slowed or stopped the spin. Samsung machines show “Ub” or “Ur”. Spread the load evenly and start the spin again.

Next steps

If it is time for a new machine, see the best washing machines in Pakistan by budget, choose the right capacity with our washing machine size guide, or browse our washing machine range. To compare types, read twin tub vs single tub.

Sources

  • Samsung Philippines, What to do when Samsung washing machine does not spin: samsung.com/ph support
  • Product specifications (wash and spin capacity, spin speed, warranty): washing machine product pages on this site.

Leave a Reply

Your email address will not be published. Required fields are marked *

Cookies on SK Electronics

We use essential cookies to run the shop, such as your cart and login. With your permission we also use Google Analytics to see how the site is used, so we can improve it. You can change your choice at any time under Cookie settings at the bottom of the page. Privacy Policy